REFURBISHED ROBOTS

Affordable Automation Solutions that Meet all OEM Specifications for Durability and Repeatability

Purchase one of our Refurbished Robots or Send us Yours

We have refurbished hundreds of Fanuc Robots. Our experience, facilities and access to parts enables us to deliver a robot that meets all OEM specifications and exceeds your expectations.

Our Refurbishment Process consists of:

Evaluation

Robot evaluations consist of a pre-power up inspection of cables connectors, motor caps, fans, switches/pushbuttons, seals, proper PC board connections, loose items and other physical concerns which could potentially be problematic when power is applied. After which the robot will run a repeatability/durability/backlash test for a minimum of ten (10) continuous hours with a full payload, through full range of motions evaluating the robot's ability to meet the OEM specifications of repeatability. This is followed by another inspection of mechanical and electrical components and a report of our findings is generated and provided to the customer.

Refurbishment

Our industry-leading refurbishment process covers every aspect of the arm/controller system to ensure the finished product meets all OEM specifications for durability and repeatability. A typical scope of work includes:

Controller:

Clean inside and outside of controller cabinet
Clean heat exchanger
Inspect Controller for OEM Engineering Changes
Remove and clean all PCB's
Clean connector contacts
Replace fan filters
Replace cooling fans (when applicable)
Replace batteries
Delete old files from memory board (optional)
Replace any missing covers
Paint Controller (optional)
Perform functionality test on Teach Pendant
Prepare for shipment

Mechanical:

Clean mechanical unit
Disconnect all cable connectors
Clean all contact pins and plugs
Clean drive components
Replace lubricants per OEM specification
Master the robot (when applicable)
Paint Robot (optional)
Adjust over-travel limit switches (optional)
Install witness marks
Run a verification test of a minimum of fifty (50)
cycles to confirm proper operation and cable connections prior to completion.

Request a Quote

Our Refurbished Fanuc Robot Inventory

Arc Mate 100iC w/ R-30iB

Arc Mate 120iC w/ R-30iB

LR Mate 200iC w/ R-30iA

M-10iA w/R-30iA and R-30iB

M-16iB/20 w/ R-30iA

M-710iC/50 w/ R-30iB or R-30iA

M-710iC/50 with R-30iB or R-30iA

M-20ia w/ R-30iA or R-30iB

M-900iA/260L w/ R-30iA

M-900iA/350 w/ R-30iA

M-900iA/400L w/ R-30iA

M-900iB/700 w/ R-30iB

R-2000iA/125L w/ R-J3iB

R-2000iA/165F w/ R-J3iB

R-2000iB/100P w/ R-30iA

R-2000iB/210F w/ R-30iA

R-2000iB/125L w/ R-30iA

R-2000iC/125L w/ R-30iB

R-2000iC/165F w/ R-30iB

R-2000iC/210F w/ R-30iB

Here are highlights of an actual customer's R-2000iB refurbishment journey.

This Fanuc R-2000iB had seen a good bit of typical use, but was still a good candidate for refurbishment.	The robot was covered in a mixture of grease and metal shavings	Years of wear has chipped and even removed much of the paint.
Every exposed surface is coated in grime.	The cabling was worn and the protective coverings were in need of replacing.	Our refurbishment process begins with a thorough cleaning. Once clean, an inspection of all mechanical and electrical components can begin.
Axis 1 would not meet repeatability specs for backlash. Upon its removal small pieces of the gear assembly were found in the grease. It had to be replaced.	The bodywork is complete and the robot is in the process of being prepped for paint.	All the motors were either replaced, repaired or repainted depending on the condition and need.
All cable connectors are cleaned and inspected.	With a fresh paint job in the original FANUC yellow – complete with black accents, this robot has a new lease on life. It is almost indistinguishable from a new robot.	Complete with new arm tags and cable covers, the fully refurbished robot has been load tested to ensure it meets all OEM standards and is about to be bolted, banded and shipped back to a happy customer.